1Research building
This facility is the main building of Fukushima Robot Test Field, where can use for various tests against wind, rain, waterproof, dustproof, fog, water pressure, temperature, humidity, vibration, and radio wave about performance evaluation of robot. It also can use for preparation, processing and measurement for each test. This facility can be used as a short/long term base for researchers, an office, and hold a large-scale conference or an exhibition. In addition, Fukushima Technology Centre Minamisoma Technical Support Centre, installed in the ward, will provide equipment support, technical consultations and development support.
1Research building
・Floor space : approx. 5,200㎡ ・Reinforced concrete construction(2stories) ・Parking area for approx. 165 cars
ALaboratory
| 30 – 60㎡ 20 rooms office desk 2, office chair 2, Bookshelf 1(laboratories 1 – 13 are equippeda mini kitchen.)(Room 201-204 can also be used asconference rooms.) |
BConference room
| 3 rooms for 20 – 40 people |
CGeneral control room
| For operation management while looking at the unmanned aircraft facilities |
DIndoor examination-place
| Floor space 32×30m Ceiling height 11m Overhead travelling crane 2t Epoxy resin type floor covering on floor concrete Carry in entrance W7m×H4.1m Pressure test equipment |
ECourtyard
| Courtyard with half roof(36×18m) can use for test preparation |
FConference hall
| For 180 people (theater type) |
GRoom 101 and 102 (Laboratory/Development laboratory)
| 2 room( For short-term stay, 40 ㎡) single phase 100V,single phase 200V |
HInstrument Analysis Room/Precision Measurement Room/Dust test room
IProcessing room
JEnvironmental measurement room
KAnechoic chamber
LVibration test room
MTest room for wind resistance・rainfall/Waterproof test room
NRental warehouse/Depository
| 30 – 100㎡ 15 rooms 2ton overhead travelling crane (only in Depository) Carry in entrance W2,690 mm/3,790 mm/ 4,300 mm x H4, 100 mm Epoxy resin type floor covering on floor concrete |
OManagement office
PShower room
QMini workshop, electronic control room
Fee
| Facility / Equipment | Fee | ||||
|---|---|---|---|---|---|
| One month | AM (9:00-13:00) |
PM (13:00-17:00) |
Nighttime (per hour) (17:00-21:00) |
Extratime (per hour) (0:00-9:00, 21:00-24:00) |
|
|
FConference hall
|
－ | 14,100JPY | 14,100JPY | 4,300JPY | 4,600JPY |
|
FConference hall(including foyer)
|
－ | 19,000JPY | 19,000JPY | 5,700JPY | 6,200JPY |
|
BConference room 1
|
－ | 5,600JPY | 5,600JPY | 1,700JPY | 1,800JPY |
|
BConference room 2
|
－ | 5,400JPY | 5,400JPY | 1,700JPY | 1,800JPY |
|
BConference room 3
|
－ | 5,400JPY | 5,400JPY | 1,700JPY | 1,800JPY |
| Facility / Equipment | Fee | ||||
|---|---|---|---|---|---|
| One month | AM (9:00-13:00) |
PM (13:00-17:00) |
Nighttime (17:00-21:00) |
Extratime (per hour) (0:00-9:00, 21:00-24:00) |
|
|
BRoom 201 (Laboratory / conference room)
|
91,300JPY | 5,500JPY | 5,500JPY | 6,600JPY | 1,800JPY |
|
BRoom 202 (Laboratory / conference room)
|
93,300JPY | 5,500JPY | 5,500JPY | 6,600JPY | 1,800JPY |
|
BRoom 203 (Laboratory / conference room)
|
94,600JPY | 5,300JPY | 5,300JPY | 6,400JPY | 1,800JPY |
|
BRoom 204 (Laboratory / conference room)
|
91,400JPY | 5,200JPY | 5,200JPY | 6,200JPY | 1,700JPY |
|
GRoom 101
(Laboratory / development laboratory) |
78,700JPY | 4,800JPY | 4,800JPY | 5,700JPY | 1,600JPY |
|
GRoom 102
(Laboratory / development laboratory) |
77,900JPY | 4,700JPY | 4,700JPY | 5,700JPY | 1,600JPY |
|
DIndoor examination place
|
－ | 50,300JPY | 50,300JPY | 60,400JPY | 16,400JPY |
|
DIndoor examination place (when using half space)
|
－ | 26,400JPY | 26,400JPY | 31,700JPY | 8,600JPY |
| Facility / Equipment | Fee | |
|---|---|---|
| Period of use | Fee | |
|
ALaboratory 1
|
One month | 109,100JPY |
|
ALaboratory 2
|
One month | 105,700JPY |
|
ALaboratory 3
|
One month | 108,700JPY |
|
ALaboratory 4
|
One month | 108,600JPY |
|
ALaboratory 5
|
One month | 108,700JPY |
|
ALaboratory 6
|
One month | 111,500JPY |
|
ALaboratory 7
|
One month | 105,900JPY |
|
ALaboratory 8
|
One month | 108,600JPY |
|
ALaboratory 9
|
One month | 108,700JPY |
|
ALaboratory 10
|
One month | 110,500JPY |
|
ALaboratory 11
|
One month | 72,500JPY |
|
ALaboratory 12
|
One month | 62,300JPY |
|
ALaboratory 13
|
One month | 62,300JPY |
|
ALaboratory 14
|
One month | 62,300JPY |
|
ALaboratory 15
|
One month | 62,300JPY |
|
ALaboratory 16
|
One month | 74,800JPY |
| Facility / Equipment | Fee | |
|---|---|---|
| Period of use | Fee | |
|
NDepository
|
All day | 9,300JPY |
|
NDepository
(when using half space) |
All day | 5,900JPY |
|
NRental
warehouse 1 |
One month | 59,500JPY |
|
NRental
warehouse 2 |
One month | 59,900JPY |
|
NRental
warehouse 3 |
One month | 58,300JPY |
|
NRental
warehouse 4 |
One month | 59,500JPY |
|
NRental
warehouse 5 |
One month | 59,900JPY |
|
NRental
warehouse 6 |
One month | 58,300JPY |
|
Rental
warehouse 7 |
One month | 21,400JPY |
|
Rental
warehouse 8 |
One month | 21,400JPY |
|
Rental
warehouse 9 |
One month | 21,400JPY |
|
Rental
warehouse 10 |
One month | 21,400JPY |
|
Rental
warehouse 11 |
One month | 21,400JPY |
|
Rental
warehouse 12 |
One month | 21,400JPY |
|
Rental
warehouse 13 |
One month | 21,400JPY |
|
Rental
warehouse 14 |
One month | 21,400JPY |
|
PShower room
|
One time | 200JPY |
2Test Preparation Building3Outdoor test pad4Measurement shed A5Measurement shed BFor Preparation of test and maintenance of robot
Test Preparation building
| Steel framed structure 2 stories,approx.220㎡ | |
| maintenance room | 70.7㎡ |
|---|---|
| Preparatory office 1 | 45.0㎡ |
| Preparatory office 2 | 74.6㎡ |
| Restroom | |
Outdoor test preparation place
| 20m×25m(Concrete pavement) |
Simple measurement room A/B
| Light gauge steel construction, Flat house, Floor space 24.3 ㎡ Office space 16.8 ㎡, restroom , kitchen Refrigerator, electric kettle, microwave oven |
Fee
| Facility / Equipment | Fee | |||
|---|---|---|---|---|
| AM (9:00-13:00) |
PM (13:00-17:00) |
Nighttime (17:00-21:00) |
Extratime (per hour) (0:00-9:00, 21:00-24:00) |
|
|
2Test preparation building (Maintenance room)
|
7,000JPY | 7,000JPY | 8,400JPY | 2,300JPY |
|
2Test preparation building (Preparatory Office 1)
|
5,700JPY | 5,700JPY | 6,800JPY | 1,900JPY |
|
2Test preparation building (Preparatory Office 2)
|
7,500JPY | 7,500JPY | 9,000JPY | 2,500JPY |
|
3Outdoor test preparation place
|
4,300JPY | 4,300JPY | 5,200JPY | 1,400JPY |
|
4Simple measurement room A
|
6,100JPY | 6,100JPY | 7,300JPY | 2,000JPY |
|
5Simple measurement room B
|
6,900JPY | 6,900JPY | 8,300JPY | 2,300JPY |
Equipment list
Machining equipment
| Machining equipment | Type | Spec | Fee |
|---|---|---|---|
|
IMachining center
|
VARIAXIS j-600/5X AM Wire arc metal lamination | Movement : 850mm (X axis), 550mm (Y axis), 510mm (Z axis), -120 – 90°(B axis), 360°(C axis) Lamination method : Wire arc metal lamination Laminatable metal : Aluminum, Stainless steel, Mold steel, Heat resistant alloy, etc. | 12,960JPY per hour |
|
INC milling cutter
|
KE55 | General purpose operation, Machining guidance operation and NC program operation are availableMovement : 550mm (X) ×320mm (Y) ×350mm (Z) Table size (work space) : 800mm×375mm Spindle rotational speed : 40 – 4,000rpm |
2,130JPY per hour |
|
ISemi-automatic lathe
|
TAC-360 | General purpose operation, Interactive input operation, Machining by CNC programming are available Distance between both centers : 770mm Spindle speed range : 60 – 2,000rpm | 1,110JPY per hour |
|
IDrilling machine
|
B 23S | Maximum processing capacity : ф23mm Spindle rotations : 2,400rpm, 1,320rpm, 830rpm, 400rpm | 140JPY per hour |
|
IContour machine
|
VZ-300SA | Cutting ability : 200mm (H) × 300mm (D) Table stroke : 250mm | 180JPY per hour |
|
IHigh-speed cut-off machine
|
HS-100G2 | Standard cutting ability : 45mm (Pipe material), 40mm(Solid material), Plate material (20mm×75mm) | 420JPY per hour |
|
IShearing machine
|
AST-1313 | Cutting thickness : 13mm (approx. SS400 equivalent) Cutting length : 1,280mm | 1,850JPY per hour |
|
ICutting dynamometer
|
9139AA | Measuring range (when loaded on a plate) : ±30kN (Fx,Fy,Fz), ±3,000N・m (Mx,My,Mz), Top plate : 140mm×190mm | 1,510JPY per hour |
|
IDouble-headed grinder
|
FG255T | Grinding wheel outer diameter : ф255mm × 25 mm (thickness) rotational speed : 1,500 rpm | 110JPY per hour |
|
IBelt grinder
|
FS-2N | Belt width : 100 mm Belt speed : 17.2 m/s (50Hz) | 110JPY per hour |
|
Q3D printer (1)
|
L-DEVO F300TP | Fabrication method : Fused deposition method Fabrication size (mm) : 310(W)×310(D)×450(H) Fabrication material (example) : H-PLA、ABS | 920JPY per hour |
|
Q3D printer (2)
|
F170 | Fabrication method : Fused deposition method Fabrication size (mm) : 254(W)×254(D)×254(H) Fabrication material (example) : PLA、ABS Support material : WaterWorks soluble support method | 1,780JPY per hour |
|
Q3D printer (1)(FDM type) Molding resin
|
– | 3D printer (1) (FDM type) Molding resin | 60JPY/10g |
|
Ｑ3D printer (2)(FDM type) Molding resin
|
– | 3D printer (2) (FDM type) Molding resin | 830JPY/10g |
Material processing equipment
| Material processing equipment | Type | Spec | Fee |
|---|---|---|---|
|
ISputtering device
|
MC1000 | Film forming material : Pt, Pt-Pd, Au, Carbon | 400JPY per hour |
|
ISample polishing system
|
Ecomet300 pro / Automet300 | Polishing plate size : 10 inch Polishing plate rotation speed : 50 – 400rpm | 940JPY per hour |
Analytical equipment
| Analytical equipment | Type | Spec | Fee |
|---|---|---|---|
|
HScanning electron microscope
|
S-3700N | Elements can be analyzed : B – U Magnification : 15 x – 300,000 x Maximum sample size : ф300mm |
4,460JPY per hour |
|
HMeasuring microscope
|
MF-UK4020D | Measurement range : 400 mm × 200 mm, Maximum height of test object 220 mm Observation mode : bright field, dark field, differential interference, simplified polarization Measurement accuracy : (2.2+0.002L) μm |
980JPY per hour |
|
HFourier transform
infrared spectroscopy system |
Spotlight200i-DTGS SpectrumTWO | Measurement wave number range : 8,300 – 350cm-1、 7,800 – 400cm-1 (Microscopic) Detector : LiTaO3、DTGS (Microscopic) |
1,190JPY per hour |
|
HEnergy dispersive
X-ray fluorescence analyzer |
EA6000VX | Measurement element：Na(11) – U(92) Tube voltage and current： 50kV (Variable) /20 – 1,000μA Irradiation type : Top vertical irradiation |
1,960JPY per hour |
|
HStereomicroscope
|
S9i | Magnification range : 6.1x – 55x Built-in camera : 10 million pixel color |
140JPY per hour |
|
ＬFFT analyzer
|
CF-9400 | Number of channels : 4 Frequency range : DC – 100kHz A / D converter : 24 bit ∆Σ type |
770JPY per hour |
|
ＬDigital microscope
|
VHX-7000 | CMOS image sensor Number of pixels: 3.19 million pixels ，Objective lens magnification: 20 ～ 6000x， Zoom lens magnification: 20 ～ 200x， Stage size: 100mm x 100mm |
1,950JPY per hour |
Electro mesurement equipment
| Electro mesurement equipment | Type | Spec | Fee |
|---|---|---|---|
|
QOscilloscope
|
Wave Runner 8254-MS | Analog band width : 2.5 GHz Channel : 4 ch (analog), 16 ch (digital) Waveform analysis tool : Serial trigger, decode, measurement/graph, eye pattern |
1,040JPY per hour |
|
QData logger
|
GL980 | Sampling interval : 1μs – 1 min Possessed probe : K type thermocouple, temperature sensor Channel : 8 ch Recordable time : 4 seconds (1μｓ) – 1 year or more (1 s) |
200JPY per hour |
|
QRadar evaluation equipment
|
DSO5804A | Measurable frequency : 75 GHz – 83 GHz (using block down converter) Analysis function : Digital modulation analysis, FMCW Radar analysis, pulse radar analysis |
4,140JPY per hour |
|
ＱSignal analyzer
|
FSW43 | Frequency range: 2Hz ～ 43.5GHz, real-time spectrum analysis width: 800MHz, I/Q analysis bandwidth: 1.2GHz |
3,350JPY per hour |
|
ＱDC stabilized power supply
(18V specification) |
DC30-36 | Output rating (Voltage : 30V Current : 36A Power : 360W) |
130JPY per hour |
|
QDC stabilized power supply
(60V specification) |
DC80-27 | Output rating (Voltage : 80V Current : 27A Power : 720W) | 140JPY per hour |
|
QAC stabilized power supply
(single-phase specification) |
DP015S | Power capacity : 1.5kVA Rated Output Voltage : 100V/200V Maximum Current : 15A/7.5A Frequency Setting Range : 40Hz – 550Hz |
190JPY per hour |
|
QDigital multimeter
|
34470A | Resolution : 7 1/2digit， DC voltage (range : 100mV – 1,000V, minimum resolution : 10nV)， AC voltage (range : 100mV – 750V, minimum resolution : 10nV, frequency band : 3Hz – 300kHz) ， Resistance (range : 100Ω – 1GΩ, minimum resolution : 10μΩ）， DC current (range : 1μA – 10A, minimum resolution : 100fA)， AC current (range : 100μA – 10A, minimum resolution : 10pA, frequency band : 3Hz – 10kHz) |
260JPY per hour |
|
QImpedance analyzer
|
65120B | Measurement frequency range : 20Hz – 120MHz Measurement range : 0.01mΩ – 2GΩ， measurement parameters : Z,θ, C, D, L, Q, R, X, G, B, Y fixture : for lead parts, for chip parts, for thin films |
850JPY per hour |
|
QField test system
(Handheld Microwave Analyzer) |
N9950A | CAT / VNA frequency: 300 kHz ～ 32 GHz, spectrum analyzer frequency: 9 kHz ～ 32 GHzoptional functions: power meter, channel power measurement, real-time spectrum analysis, I/Q signal analysis, etc. |
3,160JPY per hour |
|
QNetwork analyzer
|
E5061B | Frequency range: 5Hz ～ 3GHz, options: gain / phase test port, impedance analysis function, various test fixtures |
2,000JPY per hour |
|
QArbitrary waveform generator
|
WF1968 | Number of channels: 2Ch, frequency: 0.01μHz ～ 200MHz (sine wave), sampling rate: 420MSa/s, modulation method: FM, FSK, PM, PSK, AM, DC offset, PWM |
240JPY per hour |
Physical properties equipment
| Physical properties equipment | Type | Spec | Fee |
|---|---|---|---|
|
HVickers hardness tester
|
HMV-G21DT | Sample stage space : 100mm×100mm Maximum sample height capacity : 100mm Ability : 98.07mN – 19.61N | 530JPY per hour |
|
HRockwell hardness tester
|
RMT-1 | Maximum sample height capacity : 200mm Maximum sample depth capacity : 165mm Ability : 588.4N, 980.7N, 1471N | 420JPY per hour |
|
IUniversal material testing machine
|
AG-100KNXPlus | Maximum load capacity : 100kN Effective test width : 930mm Crosshead movement : 1,330mm (Without jig) | 2,320JPY per hour |
Dimensions・shape measurement equipment
| Dimensions・shape measurement equipment | Type | Spec | Fee |
|---|---|---|---|
|
HX-ray CT scanner
|
TOSCANER-24500AVFD | X-ray tube output : Maximum 450kV / 3.3mA Line detector /flat panel detector switchable Scan area : ф600 mm × H 1,000 mm | 14,450JPY per hour |
|
HCNC 3-D measuring machine
|
STRATO-Apex9166 | Measurement range : 900mm (X axis) 1,600mm (Y axis) 600mm (Z axis) Measurement error range : E0,MPE＝0.9 +2.5L/1,000 (μm) | 7,680JPY per hour |
|
HMeasuring machine for Surface
coarseness andOutline shape |
SV-C4500L8 | Measurement range : 200mm ( X axis (drive unit)) 60mm (Z1 axis (detection unit)) | 1,070JPY per hour |
|
HNon-contact 3-D digitizer
|
ATOS Compact Scan 12M | CCD camera pixel number : 12 million pixels × 2 Measurement range : 170mm×130mm×110mm, 390mm×290mm×250mm, 700mm×500mm×500mm | 2,690JPY per hour |
Environmental equipment
| Environmental equipment | Type | Spec | Fee |
|---|---|---|---|
|
DPressureproof test equipment
|
－ | Pressurize by water. Maximum pressure : 2.2 MPa Container size : ф1.5 m , 1.5 m(H) | 4,490JPY per hour |
|
HEarthly affairs test device
|
DTS-2019-SP5 | Can test based on IP5X, IP6X Tank size：1,500(W)×1,500(D)×1,000(H) mm Maximum sample weight：150kg | 3,280JPY per hour |
|
JTemperature and humidity
testing chamber |
EC-16MHHP | Tank size : 500mm (W) ×380mm (D) ×630mm (H) Temperature range : -40 – 150°C Humidity range : 20 – 98％RH | 380JPY per hour |
|
JDecompression Temperature
andhumidity testing chamber |
ALT-7018-3400-HW | Tank size : 1,500mm (W) ×1,500mm (D) ×1,500mm (H) Temperature range : -70 – 180°C (Atmospheric pressure) -70 – 140°C (Below atmospheric pressure – 33.4kPa) Humidity range : 20 – 95％RH (Atmospheric pressure) 20 – 85％RH (69.7kPa) Pressure control range : 10.7 – 101kPa (Absolute pressure) |
2,180JPY per hour |
|
JThermal shock testing equipment
|
ES-77LH | Tank size : 410mm (W) ×360mm (D) ×490mm (H) Temperature range : -70 – 0°C (Low temperature exposure), 60 – 200°C (High temperature exposure) | 770JPY per hour |
|
JHigh acceleration
life testingequipment |
PC-422R8 | Tank size : 420mm (ф) ×485mm (D) Temperature range : 105.0- 133.3°C (100%RH) 110.0 – 140.0°C (85%RH) 118.0 – 150.0°C (65%RH) Humidity range : 65 – 100％RH Pressure range : 0.019 – 0.208MPa |
300JPY per hour |
|
JDrying furnace
|
VTEC-216-H | Tank size : 600mm (W) ×600mm (D) ×600mm (H) Temperature range : 60 – 300°C | 140JPY per hour |
|
LTwo axes reshuffling
vibration testing equipment |
VTS-60ES-2 ／ 150 Type | Testable waveform : Sine wave (Steady, Sweep : linear/logarithm), Random wave Test frequency range : 3Hz -200Hz Maximum acceleration : 49m/s2 Maximum loading : 500kg Table size : 1,500mm×1,500mm |
4,450JPY per hour |
|
LSingle axis vibration
testingequipment |
FC-080K ／ 60 Type | Testable waveform : Sine wave (35kN), Random wave (35kNrms), Shock wave (87.5kN) Test frequency range : DC -2,000Hz Maximum acceleration : 889m/s2 (Sine wave no load), Maximum loading : 500kg Available for combined test | 4,310JPY per hour |
|
LTempurature and humidity
testing chamber (Compound test) |
VC-102DWMX(32)P3G-H/V | Tank size : 1,000mm (W) ×1,000mm (D) ×1,000mm (H) Temperature range : -40-150°C Humidity range : 30-98％RH | 1,690JPY per hour |
|
MWaterproof test equipment
|
IPX-3456-TBSP | Can test based on IPX3, IPX4, IPX5, and IPX6 | 2,520JPY per hour |
|
MThe rain・drizzle test device
|
FRTF-HRS200V-180 | Precipitation : 10 – 180mm approx 3mm/h (Drizzle) Particle size (raindrop diameter) : approx. ф1mm, approx. ф3mm Rainfall range : 4m×4m×Height 4m | 2,780JPY per hour |
|
MWind-resistant test device
|
Jet GYM GRL-8041 | Fan diameter : ф800mm Wind speed and reach distance : 5m/s(20m) 1.5m/s(70m | 240JPY per hour |
Anechoic chamber
| Anechoic chamber | Type | Spec | Fee |
|---|---|---|---|
|
KAnechoic chamber
|
3m Radio anechoic chamber | Space : 8.5m (L) ×5.0m (W) ×5.6m (H) Turntable : ф2.0m Antenna lift range : 1 ? 4m Measurable frequency band : 30MHz ? 18GHz |
9,040JPY per hour※1 |
|
K3-D radiation pattern measurement system
|
－ | Measurement frequency range : 700 MHz-6 GHz Rotation range : Measurement by gantry (horizontal; 360°, vertical : ±165°) Measurement coordinate system : Spherical coordinates |
7,270JPY per hour |
|
KTRP/TIS measurement system
|
－ | Communication method : LTE (FDD), TD-LTE, IEEE802.11 b/g/a/n/ac, etc. |
8,940JPY per hour |
|
KGNSS receiving system
sensitivity evaluation system |
－ | Supported satellite : GPS, QZSS, Galileo, etc. | 2,750JPY per hour |
|
KMultipath phasing evaluation system
|
－ | Test frequency range : 380 MHz ? 6 GHz Phasing pattern : Rayleigh phasing |
5,370JPY per hour |
|
KRadiation EMI measurement system
|
－ | Measuring frequency range : 30 MHz ? 6 GHz Applicable standard : CISPR32, VCCI |
4,170JPY per hour |
|
KRadiation immunity test system
|
－ | Test frequency range : 80MHz ? 4GHz(Max30V/m), 4GHz ? 6GHz(Max10V/m) Applicable standard : IEC61000-4-3 |
8,800JPY per hour |
Other equipment
| Other equipment |
Type | Spec | Fee | Extratime (per hour) (0:00-9:00, 21:00-24:00) |
||
|---|---|---|---|---|---|---|
| AM (9:00-13:00) |
PM (13:00-17:00) |
Nighttime (17:00-21:00) |
||||
|
2Fume simulator
|
PS-2006 | Smoke ability : 10 – 31m3/min (Variable) Smoke reach distance : 3m (Windless time) |
100JPY※2 | 100JPY※2 | 100JPY※2 | 20JPY per hour |
|
2Victim simulator
|
WRR-25 | Material : PVC plastic resin Body weight : 24.9kg±4％ Height : 160cm±5cm |
400JPY | 400JPY | 400JPY | 90JPY per hour |
|
2Outdoor large
monitor system |
LEDVISION | Monitor size : 4,000mm×2,000mm Viewing angle : 150 (°Horizontal) 120 (°Vertical) Contrast ratio : 5,000:1 Maximum brightness : 5,000NITS (cd/m2) |
7,400JPY | 7,400JPY | 7,400JPY | 1,840JPY per hour |
|
2Light projector
|
LS304D | LED energy consumption : 300W × 4 light Power Generator : 2kVA (50Hz) |
400JPY※2 | 400JPY※2 | 400JPY※2 | 90JPY per hour |
|
2Generator
|
DGM600MK | Can output simultaneous Three-phase ・ single-phase three line Rated output : Three-phase four-line 50 / 60kVA, single-phase three-line 30 / 36kVA Outlet:6 pieces |
400JPY※2 | 400JPY※2 | 400JPY※2 | 90JPY per hour |
|
2High-speed camera
|
SA-Z type RX-HK | Color photographing Pixel number : 1,024×1,024 pixel Maximum shooting speed (full frame) : 20,000fps Maximum shooting speed (Dividedframe) : 2,100,000fps |
4,700JPY | 4,700JPY | 4,700JPY | 1,170JPY per hour |
|
2Picture record system
|
－ | Network camera： 4K fixed type and HD image quality fixed type・ movable type Portable camera： 4K Handy Type and Small Type Image recording apparatus : Image of network camera and a portable camera can be edited simultaneously |
5,000JPY | 5,000JPY | 5,000JPY | 1,230JPY per hour |
|
2Rental tent
|
－ | Width6,000mm× Depth3,000mm(Assembled) With water injection type weight |
100JPY | 100JPY | 100JPY | 20JPY per hour |
|
23D motion capture
|
OQUS7+ | Sampling : 300fps (12 million pixels), 1,100fps (3 million pixels) Maximum sampling : 10,000fps Can measure in outdoor | 5,900JPY | 5,900JPY | 5,900JPY | 1,480JPY per hour |
※1 Separate fee for each test equipment is added.
※2 Fuel cost (or smoke agent cost) is not included.
※2 Fuel cost (or smoke agent cost) is not included.
Remarks
(1) A.M.: 9:00 a.m. to 1:00 p.m., P.M.: 1:00 p.m. to 5:00 p.m., Nighttime: 5:00 p.m. to 9:00 p.m., All day: 12:00 a.m. to 12:00 a.m., Extratime : 1 hour during 12:00 a.m. to 9:00 a.m. and 9:00 p.m. to 12:00 a.m.
(2) The same amount as fee is added when it falls under any of the following.
1. When holding an event by collecting admission fee, attendance fee, or membership fee for a prot. 2. When using for any prot-making activities, such as selling goods,commercial advertisement, etc.
(3) Fee is reduced to 70%, when using for preparation.
(4) When using continuously for two days or more, fee is not occured from the night to early morning, as far as it is used for storage of display items and equipment.